Bacharach Flue-Gas Sample Conditioning System Dokumentacja Strona 70
- Strona / 86
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Maintenance ECA 450
66 Instruction 0024-9400
4.4.2 Nitric Oxide Sensor Battery Replacement
A single lithium battery, located on top of the Nitric Oxide printed circuit
board, applies a bias voltage to the NO sensor to prevent the sensor from
destabilizing when the analyzer is turned off. This battery has a life
expectancy of at least 2 years.
Replace the Nitric Oxide bias battery toward the end of its life expectancy, or
when its voltage drops below 2 volts.
Tip: Replace the bias battery whenever the NO sensor is replaced.
Material Required:
• Medium Phillips screwdriver
• Bias battery (refer to Section 6.1)
Procedure:
1. Remove two screws from sensor-cover plate, and then remove plate to
gain access to sensor compartment. See Figure 4-3.
2. Remove old battery from its holder on the Nitric Oxide printed circuit
board.
3. Insert new battery (positive side facing upwards) into holder.
4. Install sensor-cover plate that was removed in Step 1.
5. Before powering up and using the analyzer, allow the Nitric Oxide sensor
to stabilize as described below. Note that recalibration of the Nitric Oxide
sensor is not required after replacing its bias battery.
Depending on how long the Nitric Oxide sensor was without bias voltage,
the time required for the sensor to completely stabilize varies from less
than a minute to several days. Typical stabilization times are shown
below. Generally, however, the sensor is sufficiently stable after 4 hours
for measurement purposes.
Bias removed for . . . Stabilization time
Less than 15 minutes Less than 1 minute
Less than 1 hour Less than 5 minutes
Less than 2 days Less than 4 hours
Greater than 2 days Up to 2 days
- Model 450 1
- Notice: 2
- Table of Contents 3
- Contents ECA 450 4
- 1 Introduction 5
- 1.3 Technical Data 6
- Accuracy: 7
- 4 Instruction 0024-9400 8
- 1.4 Operation Overview 9
- Introduction ECA 450 10
- 6 Instruction 0024-9400 10
- 1.5.3 POWER (AC Adapter) 11
- 1.5.6 OPT (Option) 11
- 8 Instruction 0024-9400 12
- CALIBRATE 13
- 10 Instruction 0024-9400 14
- 2 Operation 15
- 2.3 Fuel Selection 16
- ECA 450 Operation 17
- Instruction 0024-9400 17
- Operation ECA 450 18
- 14 Instruction 0024-9400 18
- 2.7 Saving Test Data 20
- 2.8 Clearing Memory 20
- 18 Instruction 0024-9400 22
- 2.10 Printing Data 23
- 20 Instruction 0024-9400 24
- 2.12 Data Logging 26
- 24 Instruction 0024-9400 28
- Line 1: Column Headings 30
- 2.14.1 Thermocouple Method 31
- 28 Instruction 0024-9400 32
- 2.14.3 Thermometer Method 33
- 30 Instruction 0024-9400 34
- 2.16 Statistics Mode 36
- 34 Instruction 0024-9400 38
- 2.17.1 Temperature Units 40
- 2.17.2 Pressure Units 40
- 2.17.3 Pollution Units 40
- 2.17.4 Language 41
- 2.17.5 Date 41
- 2.17.6 Time 42
- 2.17.7 O 42
- Reference 42
- 2.17.8 Test ID 43
- 40 Instruction 0024-9400 44
- 42 Instruction 0024-9400 46
- 2.17.9 Display Timeout 47
- 2.17.10 Display Format 47
- 44 Instruction 0024-9400 48
- 2.17.11 Primary Air 49
- 2.17.12 Data Logging 49
- 2.17.13 Statistics 49
- 2.17.14 User Name 49
- 2.17.15 Keypad Sound 50
- 2.17.17 Print Pressure 52
- 2.17.18 Information 52
- 3 Calibration 53
- PRESSURE 54
- ECA 450 Calibration 55
- Calibration ECA 450 56
- 52 Instruction 0024-9400 56
- 3.7 Calibrate HC Sensor 58
- 3.8 Calibrate CO-LO Sensor 59
- 56 Instruction 0024-9400 60
- 3.9 Calibrate SO 61
- Sensor 61
- 3.10 Calibrate NO Sensor 62
- 3.11 Calibrate NO 63
- 3.12 Calibrate CO-HI Sensor 64
- 4 Maintenance 65
- Maintenance ECA 450 66
- 62 Instruction 0024-9400 66
- ECA 450 Maintenance 67
- 64 Instruction 0024-9400 68
- 4.4.1 O 69
- , CO, NO, NO 69
- , & SO 69
- Sensor Replacement 69
- 66 Instruction 0024-9400 70
- 4.4.3 HC Sensor Replacement 71
- PARTICULATE FILTER 72
- (Install with arrow pointing 72
- WATER TRAP/FILTER ASSEMBLY 73
- GAS HOSE 73
- RESET BUTTON 74
- 5 Troubleshooting 76
- 5.3 Error Symbols 77
- 5.4 Troubleshooting Guide 78
- ECA 450 Parts & Service 79
- 76 Instruction 0024-9400 80
- 78 Instruction 0024-9400 82
- 6 Parts & Service 83
- 6.2 Accessories 84
- 6.3 Service Centers 85
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Bacharach Flue-Gas Sample Conditioning System
(100 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.121 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji