Bacharach Flue-Gas Sample Conditioning System Dokumentacja Strona 56
- Strona / 86
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Calibration ECA 450
52 Instruction 0024-9400
2. With the Calibrate Pressure screen displayed, and with the hose from the
calibration fixture connected to the analyzer’s PRESSURE port, adjust
the bellows for a micro manometer reading of −4 in. H
2
O column
(−10 mb).
3. Wait until the Measured reading on the screen stabilizes. Then use the
∧∨ and < > keys to enter an Applied value that equals the micro
manometer reading.
The calibration range is from –6 to –2 in. H
2
O column (−15 to −5 mb). An
applied value that is outside this range will cause the message “Bad
Calibration Entry” to appear.
Typical Calibrate Pressure Screen During Calibration:
«CALIBRATE PRESSURE«
Measured -3.40 inwc
Applied -4.00 inwc
4. Press ENTER to calibrate the analyzer’s Measured value to that of the
Applied value; after which the message “Good Calibration” should appear
along with the Calibration List screen being redisplayed.
5. Remove calibration equipment.
3.5 Calibrate T-Stack (Stack Temperature) Channel
The following procedure first zeros and then spans the stack-temperature
channel to known temperature values.
Material Required:
• Thermocouple Simulator (K-type) Range: 0 to 600 °F
Accuracy: ±0.5 °F
TS-Zero Procedure:
1. Adjust simulator to 32 °F (0 °C).
The calibration range is from 32 to 41 °F (0 to 5 °C). Any attempt to
calibrate outside this range will cause the message “Bad Calibration
Entry” to appear.
2. Plug simulator’s K-type connector into analyzer’s T-STACK jack (see
Figure 1-1).
3. Enter Calibration List screen; then choose T-Stack per Section 3.3 to
display the CALIBRATE TS-ZERO screen.
- Model 450 1
- Notice: 2
- Table of Contents 3
- Contents ECA 450 4
- 1 Introduction 5
- 1.3 Technical Data 6
- Accuracy: 7
- 4 Instruction 0024-9400 8
- 1.4 Operation Overview 9
- Introduction ECA 450 10
- 6 Instruction 0024-9400 10
- 1.5.3 POWER (AC Adapter) 11
- 1.5.6 OPT (Option) 11
- 8 Instruction 0024-9400 12
- CALIBRATE 13
- 10 Instruction 0024-9400 14
- 2 Operation 15
- 2.3 Fuel Selection 16
- ECA 450 Operation 17
- Instruction 0024-9400 17
- Operation ECA 450 18
- 14 Instruction 0024-9400 18
- 2.7 Saving Test Data 20
- 2.8 Clearing Memory 20
- 18 Instruction 0024-9400 22
- 2.10 Printing Data 23
- 20 Instruction 0024-9400 24
- 2.12 Data Logging 26
- 24 Instruction 0024-9400 28
- Line 1: Column Headings 30
- 2.14.1 Thermocouple Method 31
- 28 Instruction 0024-9400 32
- 2.14.3 Thermometer Method 33
- 30 Instruction 0024-9400 34
- 2.16 Statistics Mode 36
- 34 Instruction 0024-9400 38
- 2.17.1 Temperature Units 40
- 2.17.2 Pressure Units 40
- 2.17.3 Pollution Units 40
- 2.17.4 Language 41
- 2.17.5 Date 41
- 2.17.6 Time 42
- 2.17.7 O 42
- Reference 42
- 2.17.8 Test ID 43
- 40 Instruction 0024-9400 44
- 42 Instruction 0024-9400 46
- 2.17.9 Display Timeout 47
- 2.17.10 Display Format 47
- 44 Instruction 0024-9400 48
- 2.17.11 Primary Air 49
- 2.17.12 Data Logging 49
- 2.17.13 Statistics 49
- 2.17.14 User Name 49
- 2.17.15 Keypad Sound 50
- 2.17.17 Print Pressure 52
- 2.17.18 Information 52
- 3 Calibration 53
- PRESSURE 54
- ECA 450 Calibration 55
- Calibration ECA 450 56
- 52 Instruction 0024-9400 56
- 3.7 Calibrate HC Sensor 58
- 3.8 Calibrate CO-LO Sensor 59
- 56 Instruction 0024-9400 60
- 3.9 Calibrate SO 61
- Sensor 61
- 3.10 Calibrate NO Sensor 62
- 3.11 Calibrate NO 63
- 3.12 Calibrate CO-HI Sensor 64
- 4 Maintenance 65
- Maintenance ECA 450 66
- 62 Instruction 0024-9400 66
- ECA 450 Maintenance 67
- 64 Instruction 0024-9400 68
- 4.4.1 O 69
- , CO, NO, NO 69
- , & SO 69
- Sensor Replacement 69
- 66 Instruction 0024-9400 70
- 4.4.3 HC Sensor Replacement 71
- PARTICULATE FILTER 72
- (Install with arrow pointing 72
- WATER TRAP/FILTER ASSEMBLY 73
- GAS HOSE 73
- RESET BUTTON 74
- 5 Troubleshooting 76
- 5.3 Error Symbols 77
- 5.4 Troubleshooting Guide 78
- ECA 450 Parts & Service 79
- 76 Instruction 0024-9400 80
- 78 Instruction 0024-9400 82
- 6 Parts & Service 83
- 6.2 Accessories 84
- 6.3 Service Centers 85
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Bacharach Flue-Gas Sample Conditioning System
(100 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.115 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji