Bacharach INJECTOR CALIBRATOR CD3 Dokumentacja Strona 16
- Strona / 96
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Page 1-10 Bacharach, Inc. Instructions 67-9319
INTRODUCTION INJECTOR CALIBRATOR CD3
(c) Flowmeter Circuit (Injector Output)
(Figure 1-13)
The flowmeter circuit begins at the discharge head
which receives the injector output. Fluid passes
through a strainer & orifice, and is routed to a
3-way solenoid valve (L8) controlled by a meter
switch mounted on the control panel. When injector
is running, before the switch is actuated, injector
output is returned to the reservoir. When injector
output reading is desired, the switch is actuated,
injector output is routed through the flowmeter
before it is returned to the reservoir. The metering
system uses a patented positive displacement type
flowmeter. Fluid drives a piston in a reciprocating
motion controlled by two 3-way solenoid valves.
Motion of the piston, mechanically connected to a
linear measurement device, produces signals which
represent displaced volume. These signals and
signals generated by camshaft rotation are elec-
tronically computed. Delivery is then digitally
displayed in terms of mm
3
/stroke.
1.5 Calibration Fluid Temperature Control
System (see Chapter 5)
Calibration fluid is supplied at the injector inlet to
104°F. Two 500 watt electric immersion heaters
mounted in the reservoir heat the fluid. Cold water
flowing through a coil of copper tubing mounted in
the reservoir cools the fluid.
Figure 1-12. Injector Supply Circuit
- Rev. 8 – January, 1999 1
- TECHNICAL DATA AND FEATURES 5
- 1.0 INTRODUCTION 7
- P R E S S U R E 8
- R E G U L A T O R 8
- " A " 10
- " B " 10
- P u l l e y s C a m b o 12
- F l y w h e e l 12
- ( h i d d e n ) 12
- 2.0 INSTALLATION 19
- 2 On/Off Switch 20
- 8 Air In 2 On/Off Switch 20
- 1 Nameplate 20
- 4 Motor Rotation Direction 20
- Lift Red Ring 21
- 9 Check Regulator Setting 21
- 8 Air in 21
- to 90 psi 21
- 5 Cambox Plug 22
- 9 C a m b o x O i l 23
- 11 Intensifier Reservoi 24
- 1 Lit During Warm-up 24
- 3.0 OPERATION 27
- 5 Move to Pulley Position 29
- 3 Barring Tool 29
- (push down) 29
- 2 Tubing 30
- 5 Carrier Plate 31
- 1 PTD Injecto 31
- HOLD TO OPERATE 32
- Inlet Fuel Connector 33
- Toggle Clamp 33
- Inlet Orifice 33
- Fuel Arm 33
- 2 Adapter 34
- Plunger to Body 35
- Clamp Monitor 35
- Body to Seat 35
- Inlet Fuel Connector 36
- 3 UNCLAMP 40
- 2 HOLD TO OPERATE 40
- 6 Shim3 Barring Tool 42
- (push down) 42
- 2 Cambox Lid 6 Wrench 42
- 6 Washer and Nut5 Cam 43
- Cam 189 Shown 43
- 4 Flowmeter Tubing 44
- Manifold Inlet 45
- Tubing 45
- Swing Back Fuel Arm 45
- Front Support 45
- Injector 45
- 3 Drain Hose 47
- Swing Fuel 47
- Arm Back 47
- Plunger to Bod 48
- Timing Light 48
- Spacer Block 49
- Injector Holder 49
- Discharge Head 49
- Injector 49
- Injector 8.2 50
- Injector holder 50
- Carriage rai 50
- 4.0 MAINTENANCE & 55
- TROUBLESHOOTING 55
- 2 Reservoir drains 55
- 6 Suction filte 56
- 1 Cambox drain plug 57
- 1 Install pressure 60
- gauge here 60
- 5 Bleed por 60
- 3 Cavity (behind transducer) 61
- Limit switch 61
- 6 Optical detectors 61
- 2 Red ring 64
- 5 Encoder wheel 5 Camshaft 66
- 5.0 ILLUSTRATED PARTS LIST 69
- Page 5-3 71
- 5.2 Console, Rear View 72
- Page 5-5 73
- Page 5-7 75
- 5.4 Cabinet, Top View 75
- 5.4 Cabinet, Top View (cont.) 76
- Page 5-9 77
- 5.5 Operator’s Table 77
- 5.5 Operator’s Table (cont.) 78
- Page 5-11 79
- 5.6 Optical Detector 79
- 5.7 Cambox Assembly 80
- Page 5-13 81
- Page 5-15 83
- Page 5-17 85
- 5.11 Electrical Control Panel 86
- Page 5-19 87
- 5.12 Electrical Power System 88
- Page 5-21 89
- Page 5-23 91
- 67-6547S1R8) 92
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Bacharach INJECTOR CALIBRATOR CD3
(104 strony)Sony XBA1IP manuály
Uživatelské manuály a uživatelské příručky pro Sluchátka Sony XBA1IP.
Poskytujeme 1 manuály pdf Sony XBA1IP ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Komentarze do niniejszej Instrukcji